+49 5222 960 4810
We just need your E-Mail and shipping address.
Feel free to add more samples to your sample cart afterwards.
The floors@home collection from Project Floors offers plenty of inspiration with its wide selection of wood and stone decors.
The name PROJECT FLOORS has been associated with high-quality LVT floor coverings since 1999. The abbreviation "LVT" stands for luxury vinyl tiles and indicates that these are PVC-based floorings. The PVC designs from PROJECT FLOORS are available in ceramic concrete, sand or plain colour finishes that replicate the look of natural materials. They combine the authentic look of the original materials with the robustness and ease of care of synthetic floor coverings.
| item no. | ST76130 |
|---|---|
| Manufacturer | Project Floors |
| Collection | floors@home30 stone |
| Length in mm | 610 |
| Width in mm | 305 |
| Thickness in mm | 2 |
| Wear layer | 0,30 mm |
| Wear class | 31 Commercial (light) |
| Joint | Beveled edge (4 sides) |
| suitable for | Bath, Kitchen, Bedroom & living room, Hallway & Corridor |
| installation pattern | Tile format |
| Installation type | glue |
| Sorting (grain) | natural/classic |
| Look | Stone effect |
| Underfloor heating | suitable |
| Warranty | 10 Jahre Privat, 3 Jahre Gewerbe |
| EAN | 4250664332511 |
| Structure | Full vinyl |
| Piece per package | 18 |
| Shipping group | M |
| Colour | anthracite |
| Range of application | Residential, Commercial |
| Weight | 12,69 kg/Packing |
| Package Content | 3.34 m² |
|
Show all data ▼
|
|
| Downloads | |
Project Floors floors@home - Technical data sheet EN
|
|
|
Project Floors floors@home - Installation instruction EN
|
|
|
Project Floors floors@home - Cleaning and care instructions EN
|
|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
Variant: DIY instruction wet bed bonding & Silent Stick
button
The substrate should be permanently dry, load-bearing and even. Any unevenness should be sanded down and filled with a floor levelling compound. The surface to be laid can then be cleaned with a hoover.
CAUTION: Never install Silent Stick over a soft subfloor, e.g. carpet, cork or any type of foam underlay.
button
The vinyl planks should be stored horizontally in the room in which it is to be installed for at least 24 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.
Before laying, it is imperative that the official laying instructions, which are included in every package, are followed, otherwise any claim to warranty and guarantee will be invalidated!
Silent Stick (alternative to adhesive):
button
Now you can lay out the sheets in the opposite direction to the direction in which the top layer is laid. The foil side should always face upwards. Simply cut the Silent Stick to size with a cutter knife.
button
As soon as the strips have been laid butt to butt, the foil is removed area by area (approx. 2 planks wide) and the vinyl planks can be glued on and pressed down.
ATTENTION: There must always be a gap of approx. 5mm between the flooring and the wall and between the flooring and all fixed components.
button
Afterwards, the laid surface is rolled with a roller and the skirtings can be fixed. Please note the drying times of the adhesive. If you have a large area, we recommend that you roll the laid planks after approx. 20-30 minutes so that no air bubbles form.
Classic wet-bed gluing:
button
Before applying the adhesive, open the packages and lay the elements from different packages in alternation to obtain an even decorative pattern in the area. Mark the reference points using a chalk line and cut the vinyl planks to size with a cutter knife. The planks can now be broken by simply folding them.
button
Apply the adhesive with a notched trowel and lay the vinyl planks in the wet bed, observing the flash-off times of the adhesive. The elements should be placed in the adhesive with little tension and with tight joints and pressed on. When doing so, observe the laying direction on the back of the vinyl planks.
ATTENTION: A gap of approx. 10mm must always be maintained between the flooring and the wall as well as to all fixed components.
button
The laid surface is then rolled with a roller and the skirting boards can be fixed. Please note the drying time of the adhesive. The glued surface should be rolled after approx. 20-30 minutes so that no air bubbles form.
Material:
Tools:
optional:
Working time:
Difficulty level:
Gluing vinyl flooring - installation guide for vinyl sheets
Gluing vinyl flooring to old flooring in large rooms - planeo silent stick
Vinyl flooring XXL sticking on self-adhesive impact sound insulation
Redesigning a guest WC - sticking vinyl flooring to walls
Laying vinyl tiles on self-adhesive insulation in the WC
Clicking or sticking vinyl flooring
Grouting vinyl tiles
Subfloor testing before laying flooring
Gluing vinyl flooring to steel stairs with concrete steps
Floor spackling for vinyl flooring gluing
Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?
Replacing damaged vinyl planks on self-adhesive impact sound insulation planeo Silent stick
Are you looking for a lower price? Just ask us for an individual offer!
button 
button 
button 
button 
button 
button 
button 
button 
button 
button 
button 
button