Project Floors Click Collection presents itself in unique wood and stone decors which are available in two different wear layers of 0.55 and 0.3 mm.
- wear layer in 0.55 and 0.3 mm ideally suited for use in commercial and private areas
- environmentally friendly and non-slip higher strength, can be used without hesitation with underfloor heating and chair castors
- patented UNIFIT® locking technology
The name PROJECT FLOORS has been associated with high-quality LVT floor coverings since 1999. The abbreviation "LVT" stands for luxury vinyl tiles and indicates that these are PVC-based floorings. The PVC designs from PROJECT FLOORS are available in ceramic concrete, sand or plain colour finishes that replicate the look of natural materials. They combine the authentic look of the original materials with the robustness and ease of care of synthetic floor coverings.
|Length in mm||906|
|Width in mm||448|
|Thickness in mm||5|
|Wear layer||0,55 mm|
|Warranty||15 Jahre Privat, 5 Jahre Gewerbe|
|suitable for||Business, Industry, Bath, Kitchen, Bedroom & living room, Hallway & Corridor|
|installation pattern||Tile format|
|Look||Concrete effect, Stone effect, Tile effect|
|Underfloor heating||Warmwasser-FBH geeignet|
|Piece per package||5|
|Package Content||2.03 m²|
Show all data ▼
|Project Floors Click Collection - Datenblatt|
|Project Floors Click Collection - Verlegeanleitung|
|Project Floors Click Collection - Reinigung & Plfege|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 9pm
Sat: 9am - 2pm
Variant: DIY Instruction
Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.
CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.
The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.
Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!
Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.
Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. Lay the first plank with the tongue side facing the wall. Then snap the second plank into the first from the top on the face side. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. While folding down, the long side of the plank is clicked into the existing plank. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.
Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.
Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.
- Click vinyl flooring
- Impact sound insulation
- Cutter knife
- Rubber mallet
- Measuring tape
- Skirting boards
- PE vapour barrier*
- for a room size of 15-20 m² approx. 4-5 hrs.
*required for floors with HDF core board and cork impact sound insulation
Are you looking for a lower price? Just ask us for an individual offer!