From the time it was founded in 1977, Parador has consistently set flooring standards. With the first engineered wood floor with the patented AUTOMATIC-CLICK system, Parador launched a real innovation on the market in 2000. Today, the company based in Coesfeld is active in 65 countries worldwide and has 600 employees at 3 locations. In total, the Parador product range includes more than 2500 products for floor and wall design, which fully live up to the Parador motto "living performance".
| item no. | 1730793 |
|---|---|
| Manufacturer | Parador |
| Collection | Basic 2.0 |
| Length in mm | 1219 |
| Width in mm | 229 |
| Thickness in mm | 2 |
| Wear layer | 0,30 mm |
| Wear class | 31 Commercial (light) |
| Joint | No bevel |
| suitable for | Kitchen, Bedroom & living room, Hallway & Corridor |
| installation pattern | Plank pattern (1-plank) |
| Installation type | glue |
| Sorting (grain) | natural/classic |
| Look | Wood effect |
| Wood type | Oak |
| Underfloor heating | suitable |
| EAN | 4014809192374 |
| Structure | Full vinyl |
| Piece per package | 16 |
| Slip resistance | R9 |
| Shipping group | L |
| Colour | brown |
| Range of application | Residential, Commercial |
| Weight | 17,64 kg/Packing |
| Package Content | 4.46 m² |
|
Show all data ▼
|
|
| Downloads | |
Parador Basic 2.0 - Technical data sheet EN
|
|
|
Parador Basic 2.0 - Guide EN
|
|
|
Parador Basic 2.0 - Warranty conditions EN
|
|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 6pm
Sat: 9am - 2pm
Variant: DIY instruction wet bed bonding & Silent Stick
button
The substrate should be permanently dry, load-bearing and even. Any unevenness should be sanded down and filled with a floor levelling compound. The surface to be laid can then be cleaned with a hoover.
CAUTION: Never install Silent Stick over a soft subfloor, e.g. carpet, cork or any type of foam underlay.
button
The vinyl planks should be stored horizontally in the room in which it is to be installed for at least 24 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.
Before laying, it is imperative that the official laying instructions, which are included in every package, are followed, otherwise any claim to warranty and guarantee will be invalidated!
Silent Stick (alternative to adhesive):
button
Now you can lay out the sheets in the opposite direction to the direction in which the top layer is laid. The foil side should always face upwards. Simply cut the Silent Stick to size with a cutter knife.
button
As soon as the strips have been laid butt to butt, the foil is removed area by area (approx. 2 planks wide) and the vinyl planks can be glued on and pressed down.
ATTENTION: There must always be a gap of approx. 5mm between the flooring and the wall and between the flooring and all fixed components.
button
Afterwards, the laid surface is rolled with a roller and the skirtings can be fixed. Please note the drying times of the adhesive. If you have a large area, we recommend that you roll the laid planks after approx. 20-30 minutes so that no air bubbles form.
Classic wet-bed gluing:
button
Before applying the adhesive, open the packages and lay the elements from different packages in alternation to obtain an even decorative pattern in the area. Mark the reference points using a chalk line and cut the vinyl planks to size with a cutter knife. The planks can now be broken by simply folding them.
button
Apply the adhesive with a notched trowel and lay the vinyl planks in the wet bed, observing the flash-off times of the adhesive. The elements should be placed in the adhesive with little tension and with tight joints and pressed on. When doing so, observe the laying direction on the back of the vinyl planks.
ATTENTION: A gap of approx. 10mm must always be maintained between the flooring and the wall as well as to all fixed components.
button
The laid surface is then rolled with a roller and the skirting boards can be fixed. Please note the drying time of the adhesive. The glued surface should be rolled after approx. 20-30 minutes so that no air bubbles form.
Material:
- Klebevinyl
- Planeo Silent Stick / adhesive
Tools:
- Cutter knife
- Angle
- Pencil
- Folding rule
- Toothed spatula for wet bed bonding
optional:
- Skirting boards
Working time:
- Silent Stick: approx. 3-4 hours for 15-20m².
- Wet bed bonding: approx. 6 hours for 15-20m².
Difficulty level:
- Silent Stick: easy
- Wet bed bonding: difficult
button Gluing vinyl flooring - installation guide for vinyl sheets
button Gluing vinyl flooring to old flooring in large rooms - planeo silent stick
button Vinyl flooring XXL sticking on self-adhesive impact sound insulation
button Redesigning a guest WC - sticking vinyl flooring to walls
button Laying vinyl tiles on self-adhesive insulation in the WC
button Clicking or sticking vinyl flooring
button Grouting vinyl tiles
button Subfloor testing before laying flooring
button Gluing vinyl flooring to steel stairs with concrete steps
button Floor spackling for vinyl flooring gluing
button Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?
button Replacing damaged vinyl planks on self-adhesive impact sound insulation planeo Silent stick
Individual offer?
Are you looking for a lower price? Just ask us for an individual offer!