Article no more available

Storage at the desired date - free of charge up to 9 months³
Customer service until 5pm¹ - personal & close
DIY Videos - DIY Instructions

Parador laminate flooring - 1050 4V Oak Prestige Natur

Name: Parador laminate flooring - 1050 4V Oak Prestige Natur
Brand: Parador
SKU: 1601440
Availability: InStock

32 Commercial (moderate) - V-groove (4 sides) - Wood effect - Plank pattern

Item no.: 1601440

Request alternative

Description

Technical data

DIY - Videos

We recommend the following accessories

Product description

Parador

From the time it was founded in 1977, Parador has consistently set flooring standards. With the first engineered wood floor with the patented AUTOMATIC-CLICK system, Parador launched a real innovation on the market in 2000. Today, the company based in Coesfeld is active in 65 countries worldwide and has 600 employees at 3 locations. In total, the Parador product range includes more than 2500 products for floor and wall design, which fully live up to the Parador motto "living performance".

item no.: 1601440

Technical data

item no.	1601440
Manufacturer	Parador
Length in mm	1285
Width in mm	194
Thickness in mm	8
Wear class	32 Commercial (moderate)
installation pattern	Plank pattern (1-plank)
Installation type	click
Look	Wood effect
Wood type	Oak
Special features	Blue Angel
EAN	4014809172420
Weight	18,88 kg / Packing
Joint	V-groove (4 sides)
Piece per package	10
Collection	Classic 1050
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
Range of application	Residential
Shipping group	L
Click variant	UniClic
Underfloor heating	Hydronic UFH compatible
Package Content	2,49 m²

Downloads

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate test

The substrate should be firm, even, clean, permanently dry, load-bearing, free of cracks and resistant to tension and compression. Any unevenness exceeding 3 mm must be sanded down and levelled with a floor levelling compound.

CAUTION: Never lay laminate over a soft subfloor, e.g. over carpet or on unsuitable underlays.

button

2. acclimatisation

The planks should be stored horizontally in the room in which they are to be installed for approx. 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and it will not "work" as much after the installation.

button

3. subfloor preparation

Start by cleaning the surface to be laid with a hoover. Lay out the vapour barrier (for mineral subfloors) overlapping in the room. If the laminate flooring does not already have integrated impact sound insulation, we recommend that you lay the insulation butt to butt against the laying direction of the top covering and fix all overlaps with aluminium tape.

Before installation, it is imperative that you follow the official installation instructions that are included in each package, otherwise any warranty and guarantee claims will be void!

button

4. laying instructions

Tip: To achieve as uniform a floor appearance as possible, it is advisable to install panels mixed from different packages.

You should start laying in one corner (left) and starting from the wall. Lay the first panel with the tongue side facing the wall and place all the other panels against it. Depending on the collection, the next rows are first laid with the long side into the already lying planks and fastened by applying light pressure to the face side or first clicked in with the face side and the long side then clicks into place.

ATTENTION: A distance of approx. 10-15 mm must always be maintained between the floor covering and the wall as well as to all fixed components.

button

5. last row

If possible, the last row should be half the width of the plank. To do this, please measure the exact width of the room before laying. Please also take note of the edge distances to the wall.

button

6. finish

Finally, cut off the PE foil approx. 2 cm above the floor. The skirting boards can now be attached with a mounting adhesive or the special clips.

Helpful Videos

DIY step by step

Variant: DIY-Instruction

button

1. substrate test

The substrate should be firm, even, clean, permanently dry, load-bearing, free of cracks and resistant to tension and compression. Any unevenness exceeding 3 mm must be sanded down and levelled with a floor levelling compound.

CAUTION: Never lay laminate over a soft subfloor, e.g. over carpet or on unsuitable underlays.

button

2. acclimatisation

The planks should be stored horizontally in the room in which they are to be installed for approx. 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and it will not "work" as much after the installation.

button

3. subfloor preparation

Start by cleaning the surface to be laid with a hoover. Lay out the vapour barrier (for mineral subfloors) overlapping in the room. If the laminate flooring does not already have integrated impact sound insulation, we recommend that you lay the insulation butt to butt against the laying direction of the top covering and fix all overlaps with aluminium tape.

Before installation, it is imperative that you follow the official installation instructions that are included in each package, otherwise any warranty and guarantee claims will be void!

button

4. laying instructions

Tip: To achieve as uniform a floor appearance as possible, it is advisable to install panels mixed from different packages.

You should start laying in one corner (left) and starting from the wall. Lay the first panel with the tongue side facing the wall and place all the other panels against it. Depending on the collection, the next rows are first laid with the long side into the already lying planks and fastened by applying light pressure to the face side or first clicked in with the face side and the long side then clicks into place.

ATTENTION: A distance of approx. 10-15 mm must always be maintained between the floor covering and the wall as well as to all fixed components.

button

5. last row

If possible, the last row should be half the width of the plank. To do this, please measure the exact width of the room before laying. Please also take note of the edge distances to the wall.

button

6. finish

Finally, cut off the PE foil approx. 2 cm above the floor. The skirting boards can now be attached with a mounting adhesive or the special clips.

Parador laminate flooring - 1050 4V Oak Prestige Natur

Product description

Technical data

Downloads

DIY step by step

Helpful Videos

DIY step by step

Buying laminate: What do I need to know?

Laying vinyl flooring, laminate or parquet on old carpeting - is that possible?

Laminate format variants - what decor options do I have?

Laying laminate in tile look

Cheap laminate

Checking the subfloor before laying flooring