We just need your E-Mail and shipping address.
Feel free to add more samples to your sample cart afterwards.
The HotCoating cork floor coverings are extremely hard-wearing thanks to their special coating and, with a use class of NK32, enable use in commercial areas.
- Safety The HotCoating sealing technique makes the highly elastic cork floor additionally robust. Therefore, the floor provides more safety, which opens up many new application possibilities.
- Healthy for living Cork is sound-absorbing and breathable and improves the indoor climate and the room sound. In addition, the surface is warm to the feet and barefoot-friendly.
- Environmentally conscious
KWG located in Schönau near Heidelberg is known as a reliable partner for innovative floor design. Founded in 1972 with the purpose of marketing cork flooring, KWG is now a broad-based flooring specialist for exquisite products. The manufacturer's range includes vinyl and cork floors as well as corresponding accessories for floor care. KWG showed pioneering spirit by introducing the designer vinyl ready-made floor "Antigua" for the first time in 2006. The 2017 innovation series includes the completely new mineral design floor JAVA, which can generally be used indefinitely.
|Length in mm||915|
|Width in mm||305|
|Thickness in mm||10.5|
|Underfloor heating||Warmwasser-FBH geeignet|
|Piece per package||7|
|Type||Click cork parquet|
|Package Content||1.95 m²|
Show all data ▼
|KWG HotCoating - Datenblatt|
|KWG HotCoating Korkparkett - Verlegeanleitung|
|KWG Kork - Reinigung und Pflege Objektbereich|
|KWG Kork - Reinigung und Pflege Wohnbereich|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 10pm
Sat: 9am - 2pm
The first step is to check the subfloor. All unevenness exceeding 3 mm must be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.
To allow the material to acclimatise to the room temperature and to prevent it from "working" so hard after the installation, the cork floor should be stored in the room to be installed for approx. 48 hours before the installation.
CAUTION: Never lay the cork floor over a soft subfloor, e.g. over carpet or any type of foam underlay.
Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. Now spread the vapour barrier to overlap by approx. 10 cm. If the cork floor is not already integrated with impact sound, you can lay the insulation butt to butt and tape it with aluminium tape. Pull the foil up approx. 5 cm at the edges.
Before installation, it is imperative that you follow the official installation instructions that are included in each package, otherwise any warranty and guarantee claims will be void!
Tip: To achieve as uniform a floor appearance as possible, it is recommended to install panels mixed from 2-3 different packages. The recommended installation direction is from right to left.
Click variant: Place the spacer wedges on walls, door frames, fixed wall cupboards, kitchen combinations, etc. to comply with the expansion joints. These can then be covered with an attractive skirting board. Start laying the floor on the right-hand side in the corner of the room and lay the first plank with the long side facing the wall of the subfloor. Please note the installation direction in the installation instructions. The next plank can be clicked into the end face of the plank already in place, well aligned. Depending on the collection, the planks of the second row are first connected to the front side of the lying planks or first connected to the long side and then clicked into the front side. You can help the grooves to lock by tapping them lightly with a tapping block.
Gluing variant: Apply the glue to the subfloor with a notched trowel. Lay the planks in the wet bed and fix them in place by pressing lightly. Please observe the respective flash-off times of the adhesive.
ATTENTION: A distance of approx. 10-15 mm must always be maintained between the flooring and the wall as well as to all fixed components.
Now lay all the planks by locking the grooves together. You can tighten the last row with the help of a pull iron and tap the front side tight with a rubber mallet. Finally, cut off the PU foil approx. 2 cm high and now the skirting boards can be fitted.
- Cork flooring
- Aluminium tape
- Adhesive (glue type)
- Cutter knife
- Tapping block
- Measuring tape
- jigsaw, crosscut saw
- skirting boards
- PE vapour barrier*
- approx. 4-5 hours for a room size of 15-20 m².
*required for floors with HDF core board and with cork impact sound insulation
Are you looking for a lower price? Just ask us for an individual offer!