Article no more available

Storage at the desired date - free of charge up to 9 months³
Customer service until 5pm¹ - personal & close
DIY Videos - DIY Instructions

Parador click Vinyl - Classic 2050 Oak sanded (1442063)

0,55 mm Wear layer - 42 Industrial (moderate) - Full vinyl - Beveled edge (4 sides) - Wood effect - Plank pattern - beige

Item no.: 1442063

Damp room floor.
Suitable for installation on hot water underfloor heating.
Antibacterial surface.
Comfort-Click click connection.
20-year guarantee for private use.
10-year guarantee for commercial use.

Request alternative

Description

Technical data

DIY - Videos

We recommend the following accessories

Product description

The planks in the Parador Classic collection are aesthetically pleasing, stylish, easy to install and have many possible uses.

Private, commercial and industrial use
Suitable for use in damp areas
Easy to install

Parador

From the time it was founded in 1977, Parador has consistently set flooring standards. With the first engineered wood floor with the patented AUTOMATIC-CLICK system, Parador launched a real innovation on the market in 2000. Today, the company based in Coesfeld is active in 65 countries worldwide and has 600 employees at 3 locations. In total, the Parador product range includes more than 2500 products for floor and wall design, which fully live up to the Parador motto "living performance".

item no.: 1442063

Suitable for damp locations
Underfloor heating
antibacterial
Warranty

Technical data

item no.	1442063
Manufacturer	Parador
Collection	Classic 2050
Length in mm	1209
Width in mm	219
Thickness in mm	5
Wear layer	0,55 mm
Wear class	42 Industrial (moderate)
Joint	Beveled edge (4 sides)
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
installation pattern	Plank pattern (1-plank)
Installation type	click
Wood type	Oak
Look	Wood effect
Sorting (grain)	lively/rustic
EAN	4014809145158
Piece per package	8
Structure	Full vinyl
Slip resistance	R9
Shipping group	L
Weight	17,93 kg / Packing
Colour	beige
Range of application	Commercial, Industrial
Click variant	UniClic
Underfloor heating	Hydronic UFH compatible
Package Content	2,11 m²

Downloads

Print page

DIY step by step

Variant: DIY Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. installation instructions

Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. With the tongue side facing the wall, lay the first board. Angle the end of the second board into the first. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. As the board is folded down, the long side of the board will click into the existing board at an angle. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.

button

5. finishing the last row

Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Helpful Videos

DIY step by step

Variant: DIY Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. installation instructions

Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. With the tongue side facing the wall, lay the first board. Angle the end of the second board into the first. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. As the board is folded down, the long side of the board will click into the existing board at an angle. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.

button

5. finishing the last row

Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Parador click Vinyl - Classic 2050 Oak sanded (1442063)

We recommend the following accessories

Product description

Technical data

Downloads

DIY step by step

Helpful Videos

DIY step by step

Click vinyl flooring installation guide

Laying vinyl flooring on tiles, how wide and deep can the joint be?

Is click vinyl flooring waterproof, and can it be used in bathrooms?

Checking the subfloor before installing flooring

The 10 most common mistakes when installing vinyl flooring - is it possible?

Laying vinyl flooring on old floorboards

Damp room flooring for bathrooms - sealing the flooring

Fill uneven tiles and joints

Laying floor along heating pipe

Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?