We just need your E-Mail and shipping address.
Feel free to add more samples to your sample cart afterwards.
The antigua INFINITY EXTEND vinyl floor is extremely resilient due to its 0.55 mm wear layer. In addition, it convinces with expressive and natural decors.
- robust & easy to clean the surface of the floor is made of a robust PU finish, which makes cleaning and maintenance much easier.
- micro-bevelled the panels are provided with an all-round micro-bevel. The character of the long planks is thus presented in a discreet way.
- environmentally conscious
KWG located in Schönau near Heidelberg is known as a reliable partner for innovative floor design. Founded in 1972 with the purpose of marketing cork flooring, KWG is now a broad-based flooring specialist for exquisite products. The manufacturer's range includes vinyl and cork floors as well as corresponding accessories for floor care. KWG showed pioneering spirit by introducing the designer vinyl ready-made floor "Antigua" for the first time in 2006. The 2017 innovation series includes the completely new mineral design floor JAVA, which can generally be used indefinitely.
|Collection||Antigua Infinity extend|
|Length in mm||1800|
|Width in mm||220|
|Thickness in mm||10.8|
|Wear layer||0,55 mm|
|suitable for||Business, Industry, Kitchen, Bedroom & living room, Hallway & Corridor|
|installation pattern||Plank pattern (1-plank)|
|Underfloor heating||Warmwasser-FBH geeignet|
|Special features||Integrated impact sound|
|Piece per package||4|
|Package Content||1.58 m²|
Show all data ▼
|KWG Antigua Infinity extend - Datenblatt|
|KWG Antigua - Reinigung und Pflege Objektbereich|
|KWG Antigua - Reinigung und Pflege Wohnbereich|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 10pm
Sat: 9am - 2pm
Variant: DIY Instruction
Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.
CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.
The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.
Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!
Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.
Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. Lay the first plank with the tongue side facing the wall. Then snap the second plank into the first from the top on the face side. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. While folding down, the long side of the plank is clicked into the existing plank. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.
Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.
Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.
- Click vinyl flooring
- Impact sound insulation
- Cutter knife
- Rubber mallet
- Measuring tape
- Skirting boards
- PE vapour barrier*
- for a room size of 15-20 m² approx. 4-5 hrs.
*required for floors with HDF core board and cork impact sound insulation
Are you looking for a lower price? Just ask us for an individual offer!