Article temporary not available

Storage at the desired date - free of charge up to 9 months³
Customer service until 5pm¹ - personal & close
DIY Videos - DIY Instructions

Fixed adhesive vinyl - grey pine (138391)

0.70 mm wear layer - 42 industry (normal) - full vinyl - micro bevel - wood look wideplank brown

Item no.: 138391

Suitable for use in the commercial and industrial sectors.
Has an extreme load-bearing capacity - NK33/42.
Perfect for WW underfloor heating.
Low maintenance.
Selected decors with synchronised embossing.

Processing variants:
In the bathroom/toilet: 3586207
For floating installation, use the planeo Silent Stick: 10020218PW!

Request alternative

Description

Technical data

DIY - Videos

We recommend the following accessories

Product description

item no.: 138391

Commercial and industrial areas
Underfloor heating
Suitable for damp rooms
0.7mm wear layer
durable
synchronised embossing

Technical data

item no.	138391
Length in mm	1219
Width in mm	184
Thickness in mm	2.5
Wear layer	0,70 mm
Wear class	42 Industrial (moderate)
Joint	Micro bevel
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
installation pattern	Plank pattern (1-plank)
Installation type	glue
Sorting (grain)	lively/rustic
Look	Wood effect
Wood type	Pine
Special features	Pet Friendly, Suitable for humid rooms, Non-slip, Waterproof, Synchronous embossing
EAN	7640165927427
Structure	Full vinyl
Piece per package	18.0
Style	Vintage
Slip resistance	R10
Shipping group	M
Weight	17,57 kg / Packing
Colour	brown
Range of application	Commercial, Industrial
Underfloor heating	Hydronic UFH compatible
Package Content	4,04 m²

Print page

DIY step by step

Variant: DIY instruction wet bed bonding & Silent Stick

button

1. substrate preparation

The substrate should be permanently dry, load-bearing and even. Any unevenness should be sanded down and filled with a floor levelling compound. The surface to be laid can then be cleaned with a hoover.

CAUTION: Never install Silent Stick over a soft subfloor, e.g. carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room in which it is to be installed for at least 24 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

Before laying, it is imperative that the official laying instructions, which are included in every package, are followed, otherwise any claim to warranty and guarantee will be invalidated!

Silent Stick (alternative to adhesive):

button

3. before laying

Now you can lay out the sheets in the opposite direction to the direction in which the top layer is laid. The foil side should always face upwards. Simply cut the Silent Stick to size with a cutter knife.

button

4. laying instructions

As soon as the strips have been laid butt to butt, the foil is removed area by area (approx. 2 planks wide) and the vinyl planks can be glued on and pressed down.

ATTENTION: There must always be a gap of approx. 5mm between the flooring and the wall and between the flooring and all fixed components.

button

5. finish

Afterwards, the laid surface is rolled with a roller and the skirtings can be fixed. Please note the drying times of the adhesive. If you have a large area, we recommend that you roll the laid planks after approx. 20-30 minutes so that no air bubbles form.

Classic wet-bed gluing:

button

3. before laying

Before applying the adhesive, open the packages and lay the elements from different packages in alternation to obtain an even decorative pattern in the area. Mark the reference points using a chalk line and cut the vinyl planks to size with a cutter knife. The planks can now be broken by simply folding them.

button

4. installation instructions

Apply the adhesive with a notched trowel and lay the vinyl planks in the wet bed, observing the flash-off times of the adhesive. The elements should be placed in the adhesive with little tension and with tight joints and pressed on. When doing so, observe the laying direction on the back of the vinyl planks.

ATTENTION: A gap of approx. 10mm must always be maintained between the flooring and the wall as well as to all fixed components.

button

5. finish

The laid surface is then rolled with a roller and the skirting boards can be fixed. Please note the drying time of the adhesive. The glued surface should be rolled after approx. 20-30 minutes so that no air bubbles form.

Helpful Videos

DIY step by step

Variant: DIY instruction wet bed bonding & Silent Stick

button

1. substrate preparation

The substrate should be permanently dry, load-bearing and even. Any unevenness should be sanded down and filled with a floor levelling compound. The surface to be laid can then be cleaned with a hoover.

CAUTION: Never install Silent Stick over a soft subfloor, e.g. carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room in which it is to be installed for at least 24 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

Before laying, it is imperative that the official laying instructions, which are included in every package, are followed, otherwise any claim to warranty and guarantee will be invalidated!

Silent Stick (alternative to adhesive):

button

3. before laying

Now you can lay out the sheets in the opposite direction to the direction in which the top layer is laid. The foil side should always face upwards. Simply cut the Silent Stick to size with a cutter knife.

button

4. laying instructions

As soon as the strips have been laid butt to butt, the foil is removed area by area (approx. 2 planks wide) and the vinyl planks can be glued on and pressed down.

ATTENTION: There must always be a gap of approx. 5mm between the flooring and the wall and between the flooring and all fixed components.

button

5. finish

Afterwards, the laid surface is rolled with a roller and the skirtings can be fixed. Please note the drying times of the adhesive. If you have a large area, we recommend that you roll the laid planks after approx. 20-30 minutes so that no air bubbles form.

Classic wet-bed gluing:

button

3. before laying

Before applying the adhesive, open the packages and lay the elements from different packages in alternation to obtain an even decorative pattern in the area. Mark the reference points using a chalk line and cut the vinyl planks to size with a cutter knife. The planks can now be broken by simply folding them.

button

4. installation instructions

Apply the adhesive with a notched trowel and lay the vinyl planks in the wet bed, observing the flash-off times of the adhesive. The elements should be placed in the adhesive with little tension and with tight joints and pressed on. When doing so, observe the laying direction on the back of the vinyl planks.

ATTENTION: A gap of approx. 10mm must always be maintained between the flooring and the wall as well as to all fixed components.

button

5. finish

The laid surface is then rolled with a roller and the skirting boards can be fixed. Please note the drying time of the adhesive. The glued surface should be rolled after approx. 20-30 minutes so that no air bubbles form.

Fixed adhesive vinyl - grey pine (138391)

We recommend the following accessories

Product description

Technical data

DIY step by step

Helpful Videos

DIY step by step

Gluing vinyl flooring - installation instructions for vinyl sheets

Gluing vinyl flooring to old flooring in large rooms - planeo silent stick

Glue vinyl flooring XXL on self-adhesive impact sound insulation

Redesign guest WC - stick vinyl flooring to walls

Laying vinyl tiles on self-adhesive insulation in the WC

Waterproofing bathroom - laying vinyl on walls and floor

Grouting vinyl tiles

Subfloor testing before installing flooring

Gluing vinyl flooring to steel stairs with concrete steps

Fill floor for gluing vinyl flooring

Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?

Replace damaged vinyl planks on self-adhesive impact sound insulation planeo Silent stick