With the Clever & Focus PVC floor from Gerflor, you have a floor with a low cost factor and which can be used in all living spaces.
- Environmentally friendly & healthy
The floor is 100% recyclable.
The low VOC emissions contribute to a better indoor climate.
- Hard-wearing all-rounder The special surface coating prevents scratches and stains. Suitable areas of use are: Living room, dining room, hallway, children's room, guest room, bedroom, kitchen.
- Preparation The substrate must be smooth, clean, dry, undamaged, dust-free, grease-free and even. Unroll the floor covering 24 hours before starting work so that the floor can take on the room temperature.
- Full-surface bonding
Gerflor, a leading flooring manufacturer, has a 70-year history of producing resilient floor coverings for residential and commercial applications. The French company was founded in Lyon in 1937 and always focused on innovation, healthy materials and aesthetic floor design when developing new flooring solutions. Gerflor is right about its success - numerous awards attest to the first-class quality, the design, and the environmentally friendly aspect of Gerflor products. The Red Dot Award competition honors Gerflor's Creation 70 with the Red Dot Award for Product Design 2016.
|Wear layer||0,20 mm|
|installation pattern||Plank pattern (1-plank)|
|Thickness in mm||1.3|
|Special features||Textile back|
|suitable for||Bath, Kitchen, Bedroom & living room, Hallway & Corridor|
|Piece per package||1|
|Package Content||140 m²|
Show all data ▼
|Gerflor PVC-Boden - Verlegeanleitung & Praxistipps|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 9pm
Sat: 9am - 2pm
The first step is to check the subfloor. Sand down any unevenness and fill it with a floor levelling compound. Then clean the surface to be laid with a hoover.
CAUTION: Never install PVC flooring over a soft subfloor, e.g. over carpet or any type of foam underlay.
PVC flooring should be stored in the room where it is to be installed for at least 24 hours before the installation. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.
For loose laying of an area larger than 20 m², we recommend taping the edge of the walls.
Before laying, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!
Tip: To achieve as uniform a floor appearance as possible, lay the strips in relation to each other so that the patterns match exactly and the strips overlap at the seam. Unpack the roll and roll it out on the subfloor. Use a hooked blade knife to roughly pre-cut the strips.
ATTENTION: There must always be a gap of approx. 3 cm between the flooring and the wall and between the flooring and all fixed components.
4.1 Loose laying
Stick the tape strips to all edge areas and remove the foil on the back of the tapes area by area. Now fix the floor by pressing lightly. Make a double cut at the joint of the strip. To do this, lay the sheet overlapping and cut the sheet to fit exactly along the joint. You can then make the final cut with an edge distance of approx. 2 mm. The floor should be free of tension when cutting and no objects should lie on the PVC floor.
Apply the adhesive evenly to the subfloor in strips using a notched trowel. Please observe the flash-off times specified in the data sheet. Now lay the strips in the wet bed and rub down the PVC covering. Make the final cut with an edge distance of approx. 2 mm. Finally, the substrate can be rolled with a roller to avoid air bubbles.
First, tape over the joints of the strips with masking tape. The masking tape can then be cut at the joint and now the strips are welded together with a cold welding adhesive. After approx. 1 hour, the masking tape can be removed.
Finally, you can attach and seal the skirting boards. PVC flooring can also be attached to existing skirtings with a mounting adhesive.
- PVC floor
- Adhesive (glue type)
- Hook blade knife
- masking tape
- PVC cold welding paste type T
- for a room size of 15-20 m² approx. 2-3 hours
Level of difficulty:
Are you looking for a lower price? Just ask us for an individual offer!