Article temporary not available

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Meister Parquet longlife PS 300 American Walnut vivid 8044

Plank with matt lacquered surface

Item no.: 5416008044

With a top layer of walnut.
Creates a varied installation pattern.
100% natural wood flooring.
Awarded with the Blue Angel.

Offer request

Description

Technical data

DIY - Videos

Product description

With a top layer of walnut.
Creates a varied installation pattern.
100% natural wood flooring.
Awarded with the Blue Angel.

The Residence collection from Meister offers a richly coloured selection of parquet floors with various surface treatments.

Rich in variation
Durable
Longlife guarantee

Meister gives this parquet floor a guarantee of 35 years in the living area. The Blue Angel award guarantees that the parquet is manufactured in a way that is healthy for the home and ecological. The floors from the Residence collection are low in emissions and pollutants.

MEISTER

MEISTER is the quality brand for flooring from MeisterWerke Schulte GmbH, a family-owned company. The innovative sales brand based in Ruthen-Meiste is available exclusively from specialist retailers. The wide range of floors, panels and accessories for the wood and building materials traded by MEISTER enjoys great popularity throughout Europe.

item no.: 5416008044

100% natural
warm underfoot
Underfloor heating
Blue Angel

Technical data

item no.	5416008044
Piece per package	6
Special features	Umweltfreundlich, Blauer Engel
installation pattern	Plank pattern (1-plank)
Installation type	click
Sorting (grain)	lively/rustic
Wood type	Walnut
Surface treatment	varnished
Underfloor heating	suitable
Structure	3-layer
Joint	Micro bevel
Length in mm	1187
Width in mm	142
Wear layer	2,5 mm
Collection	Residence
Shipping group	S
Manufacturer	MEISTER
Thickness in mm	13

Downloads

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate check

The subfloor should be permanently dry, load-bearing and even.

ATTENTION: Never lay parquet over a soft subfloor, e.g. over carpet, cork or any type of foam underlay.

button

2. acclimatisation

The planks should be stored horizontally in the room where they are to be installed for at least 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

Before laying, it is imperative that the official laying instructions, which are included in each package, are followed, otherwise any claim to warranty and guarantee will be invalidated!

button

3. subfloor preparation

Then clean the surface to be laid with a hoover. Any unevenness exceeding 3 mm per linear metre is sanded down and filled with a floor levelling compound.

Click:

button

4. before laying

Spread out the PE foil with an overlap of approx. 10 cm and tape it down.Now you can lay out the strips of impact sound insulation butt to butt against the laying direction of the floor covering and fix all overlaps with aluminium tape. The foil side should always face upwards.

Tip: Open several packages of the parquet at the same time and mix the planks to achieve an optimal installation pattern.

button

5. laying instructions

Lay the first plank well aligned on the subfloor, taking the edge distances into account. You can start laying the floor on the left side of the room. In the first row, the plank is clicked in with the front side. Use a rubber mallet to tap lightly on the front side so that the click connection snaps in well. In the next row, the planks are first clicked in with the long side and then the ends can be fixed by tapping lightly. To cut a plank, now take measurements and mark the plank. This is then cut with a jigsaw or crosscut saw.

ATTENTION: There must always be a gap of approx. 10 mm between the flooring and the wall and between the flooring and all fixed components.

button

6. last row

Cut the planks of the last row to size and click them in place using a pull iron. Finally, the planks can be tapped down again with a hammer.

button

7. finish

The PU foil is now cut approx. 2 cm high and the skirting boards can be fitted. Here there is the click or glue variant.

Glue:

button

4 Before gluing

Lay out the first two rows of planks and make marks in the subfloor with a pencil. The planks can be cut to size using a crosscut saw.

Tip: Open several packages of the parquet at the same time and mix the planks to achieve an optimal installation pattern.

button

5. laying instructions

Now pick up the planks again and apply the adhesive up to the marking with a notched trowel. Align the first plank and place it in the wet bed. The second plank is clicked into the already lying plank with the front side. The boards of the next row are laid first with the long side, then with the short side. Then the adhesive for the next two rows can be applied and the planks can be glued.

ATTENTION: There must always be a gap of approx. 10 mm between the flooring and the wall as well as to all fixed components.

button

6. last row

Finally, you can attach the skirting boards.

Meister Parquet longlife PS 300 American Walnut vivid 8044

Product description

Technical data

Downloads

DIY step by step

Helpful Videos

planeo parquet installation instructions

Glue down parquet - glue down parquet flooring on wooden subfloor

Floating installation parquet plank oak 1-plank UV-oiled

Discolouration of parquet - UV radiation and the effects

Parquet in the kitchen

Oiled parquet. Advantages and disadvantages

Varnished parquet. Advantages and disadvantages

Store parquet correctly - this is what you should consider before laying!

Laying herringbone parquet yourself is easy - herringbone floorboards to click on