We just need your E-Mail and shipping address.
Feel free to add more samples to your sample cart afterwards.
From the time it was founded in 1977, Parador has consistently set flooring standards. With the first engineered wood floor with the patented AUTOMATIC-CLICK system, Parador launched a real innovation on the market in 2000. Today, the company based in Coesfeld is active in 65 countries worldwide and has 600 employees at 3 locations. In total, the Parador product range includes more than 2500 products for floor and wall design, which fully live up to the Parador motto "living performance". The Parador range includes high-quality vinyl floors, engineered wood, laminate, carpets, wall and ceiling panels, screens and more. These are produced under environmentally friendly and sustainable conditions by trained specialists in Germany and Austria. Parador thus offers its customers premium quality "Made in Germany" and "Made in Austria" products. Several international awards, including the Red Dot Design Award 2009, the AIT Award 2011 and the Interior Innovation Award 2011, attest the high quality and innovative nature of Parador products.
|Length in mm||1285|
|Width in mm||194|
|Thickness in mm||8|
|installation pattern||Plank pattern (1-plank)|
|Underfloor heating||Warmwasser-FBH geeignet|
|Piece per package||10|
|suitable for||Bath, Kitchen, Bedroom & living room, Hallway & Corridor|
|Package Content||2.49 m²|
Show all data ▼
|Parador Basic 400 - Guide EN|
|Parador Basic 400 - Warranty conditions EN|
We will help you with your questions!
A specialist adviser will be happy
to advise you personally.
☎ +49 5222 960 4810
Mon - Fri: 9am - 6pm
Sat: 9am - 2pm
The substrate should be firm, even, clean, permanently dry, load-bearing, free of cracks and resistant to tension and compression. Any unevenness exceeding 3 mm must be sanded down and levelled with a floor levelling compound.
CAUTION: Never lay laminate over a soft subfloor, e.g. over carpet or on unsuitable underlays.
The planks should be stored horizontally in the room in which they are to be installed for approx. 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and it will not "work" as much after the installation.
Start by cleaning the surface to be laid with a hoover. Lay out the vapour barrier (for mineral subfloors) overlapping in the room. If the laminate flooring does not already have integrated impact sound insulation, we recommend that you lay the insulation butt to butt against the laying direction of the top covering and fix all overlaps with aluminium tape.
Before installation, it is imperative that you follow the official installation instructions that are included in each package, otherwise any warranty and guarantee claims will be void!
Tip: To achieve as uniform a floor appearance as possible, it is advisable to install panels mixed from different packages.
You should start laying in one corner (left) and starting from the wall. Lay the first panel with the tongue side facing the wall and place all the other panels against it. Depending on the collection, the next rows are first laid with the long side into the already lying planks and fastened by applying light pressure to the face side or first clicked in with the face side and the long side then clicks into place.
ATTENTION: A distance of approx. 10-15 mm must always be maintained between the floor covering and the wall as well as to all fixed components.
If possible, the last row should be half the width of the plank. To do this, please measure the exact width of the room before laying. Please also take note of the edge distances to the wall.
Finally, cut off the PE foil approx. 2 cm above the floor. The skirting boards can now be attached with a mounting adhesive or the special clips.
- Vapour barrier
- Aluminium tape
- Cutter knife
- Tapping block
- Tape measure
- Spirit level
- Skirting boards
- PE film
- For a room size of 15-20 m² approx. 4-5 hours.
Are you looking for a lower price? Just ask us for an individual offer!