Article temporary not available

Storage at the desired date - free of charge up to 9 months³
Customer service until 5pm¹ - personal & close
DIY Videos - DIY Instructions

Strong SPC click vinyl flooring - Oklahoma Oak (138841)

0.50 mm wear layer - 33 trades (intensive) - Rigid SPC - bevel (4-sided) - grey wideplank wood look

Item no.: 138841

State-of-the-art core board - mineral and highly compacted.
Rigid vinyl flooring is even easier to work with.
Less swelling and shrinkage behaviour.
Suitable for private and commercial use.
Phthalate-free - no harmful plasticisers.
Well suited for renovations due to low build-up.

Due to the rigid backing material, a very strong bond is created, but special attention must be paid to accuracy of fit during installation.

Request alternative

Description

Technical data

DIY - Videos

We recommend the following accessories

Product description

Rigid Vinyl is a new development of classic vinyl flooring and is suitable for many applications. The main differences to classic vinyl flooring are the addition of stone powder in the carrier material. They ensure very robust and rigid properties. This is why the is also known as rigid board. The rigid board improves several properties of the vinyl floor.

Low expansion and shrinkage behaviour
SPC carrier (Stone-Powder-Composite)
Resistant to deformation & dimensionally stable
enables large-area installation without expansion joints
can be laid over old floor coverings such as tiles, PVC, linoleum or old floorboards old floorboards

item no.: 138841

Mineral carrier plate
Simple processing
phthalate-free and plasticiser-free
good for renovations due to the low build-up

Technical data

item no.	138841
Length in mm	1220
Width in mm	228
Thickness in mm	3.8
Wear layer	0,50 mm
Wear class	33 Commercial (heavy)
Joint	Beveled edge (4 sides)
Warranty	25 Jahre Privat, 5 Jahre Gewerbe
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
installation pattern	Plank pattern (1-plank)
Installation type	click
Wood type	Oak
Look	Wood effect
Sorting (grain)	natural/classic
Special features	Suitable for humid rooms
EAN	7640165927571
Piece per package	10
Structure	Rigid SPC
Shipping group	M
Weight	21,68 kg / Packing
Colour	grey
Style	Modern
Range of application	Residential, Commercial
Click variant	DropDown
Underfloor heating	Hydronic UFH compatible
Package Content	2,78 m²

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness exceeding 3mm should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. laying instructions

Tips on the drop-down click system: In order to achieve the most uniform appearance of the floor, it is advisable to install panels from different packages mixed together. You should start laying in one corner (left) and starting from the wall. Lay the first plank with the tongue side facing the wall. Then snap the second plank into the first from the top on the face side. In the second row, place the plank at an angle to the long side of the row already laid and fold it down. With the help of a rubber mallet, you can lock the face of the following planks by gently hitting them. To cut a plank, now take measurements and mark the plank. Then take an angle and tear and break the plank with a multi-purpose knife/cutter.

button

5. finishing the last row

The last plank of a row should be the same length as the first plank. Place the spacers against walls, door frames, fixed wall cabinets, kitchen units etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Helpful Videos

DIY step by step

Variant: DIY-Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness exceeding 3mm should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. laying instructions

Tips on the drop-down click system: In order to achieve the most uniform appearance of the floor, it is advisable to install panels from different packages mixed together. You should start laying in one corner (left) and starting from the wall. Lay the first plank with the tongue side facing the wall. Then snap the second plank into the first from the top on the face side. In the second row, place the plank at an angle to the long side of the row already laid and fold it down. With the help of a rubber mallet, you can lock the face of the following planks by gently hitting them. To cut a plank, now take measurements and mark the plank. Then take an angle and tear and break the plank with a multi-purpose knife/cutter.

button

5. finishing the last row

The last plank of a row should be the same length as the first plank. Place the spacers against walls, door frames, fixed wall cabinets, kitchen units etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Strong SPC click vinyl flooring - Oklahoma Oak (138841)

We recommend the following accessories

Product description

Technical data

DIY step by step

Helpful Videos

DIY step by step

Click vinyl flooring installation guide

Laying vinyl flooring on tiles, how wide and deep can the joint be?

Is click vinyl flooring waterproof, and can it be used in bathrooms?

Checking the subfloor before installing flooring

The 10 most common mistakes when installing vinyl flooring - is it possible?

Laying vinyl flooring on old floorboards

Damp room flooring for bathrooms - sealing the flooring

Fill uneven tiles and joints

Laying floor along heating pipe

Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?